If you have concrete that’s gotten old and worn out, you can resurface it and make it look new again. The process is pretty simple and involves a few steps. We’ll review each of them here and give tips for choosing the best concrete resurfacing Melbourne company to handle your project.
Drill The Concrete:
Drill the concrete. A hammer drill is the best tool for this job, as it offers more control and accuracy than other power tools. The idea of drilling into your concrete is to create tiny holes to allow the epoxy resin to penetrate every area of your surface. If you don’t do this properly, it can lead to a patchy finish with no consistency between different sizes, and chips in your new concrete will appear later.
To ensure that your new finish lasts as long as possible, we recommend drilling a series of holes spaced out at around 5cm intervals (or 10cm intervals if using a minor bit). Once these holes have been drilled, use some water or vacuum pressure washing techniques to clean off any dust from around them before applying adhesive epoxy. It will help ensure no air bubbles or dust particles on top of your finished product!
Wash The Concrete:
To clean the concrete, you’ll need to use a pressure washer. Start by sweeping up any loose material from the surface with a broom. Then vacuum any dust and dirt that remains. If you have time to spare, wait 24 hours after your initial cleaning before beginning this step so that any remaining dust has time to settle.
If you’re using a concrete resurfacing as your overlay, mix two parts of water with one piece of concrete resurfacing in a large bucket or tub of water until it reaches a consistency similar to pancake batter (softer than peanut butter but not so thin that it will run off). Use paint rollers for larger areas and brushes for tight corners or other hard-to-reach places.
Remove Surface Contaminates:
- Using a brush, remove any loose debris from the concrete surface, including dust and dirt. If you are working in a damp environment, use a high-pressure water hose to dislodge mud and other materials that can be washed off with water pressure.
- Remove oil or grease stains by cleaning with an alkaline cleaner like TSP or trisodium phosphate (TSP) diluted according to instructions on its label.
- Use an abrasive disk in your drill set at a slow speed (about 500 RPM) to remove paint or wax residue from the concrete slab. Wear safety glasses and rubber gloves when working with this equipment. If you are touching surfaces when removing paint or other oils/solvents, they may contain harmful chemicals that could irritate when they come into contact with skin surfaces!
Prime The Concrete:
Prime the concrete before applying the overlays. The primer is a sealer that prevents the overlays from drying too quickly and makes them stick to the concrete better. It also prepares the surface for a longer-lasting finish.
Apply two layers of overlay, starting with a thin layer so that it’s easier to spread evenly with a roller and a thicker second layer for creating your desired surface. Using a roller helps distribute overlays more evenly than brushing on or spraying on since more surface area is being covered at once, making it easier to ensure every inch gets covered with less waste.
Once you have applied both layers of overlay, use an electric sander (not wet) to smooth out any uneven areas or ridges to create a proper texture coat if desired.
Apply The Overlays:
Once you’ve applied the overlays, you can begin to apply them. It can be done using a roller or by hand. If doing it by hand, use a trowel and smooth out any of the creases that may have been created by rolling. Make sure that you apply these in a single layer and that there are no cracks or gaps between your overlays so that your coating system can adequately adhere to them.
If using a roller, roll from bottom to top to leave minimal holes for dirt and debris to get stuck between each layer of concrete resurfacing overlay material application. However, this method ensures enough room around the edges for expansion due to moisture accumulation (which will cause cracking).
Curing And Sealing:
Curing and sealing are two critical steps in the concrete resurfacing process. Curing refers to allowing the concrete to set, while sealing is applying a protective layer over it.
It is essential because it helps prevent environmental damage and staining from penetrating the surface of your pavement. Drilling holes in concrete may also help reduce cracking, which can happen if there’s no moisture in the ground underneath or too much weight on top of it (such as heavy vehicles). These holes are called ‘dowels’ by professional contractors, who use them for additional support when repairs after cracks have formed in your driveway or sidewalk.
You Can Resurface Your Old Concrete And Make It Like New:
The next time you think about making a home improvement project, consider resurfacing your concrete. By doing so, you will be able to save money and get the look that you have always wanted with just a straightforward procedure.
For your concrete to last longer, it needs proper maintenance. Resurfacing is one such way of extending its life by making it look new! Re-surfacing can also help prevent cracking and give protection against stains such as oil leaks or other chemicals that may come into contact with the surface. During everyday use over time due to exposure factors when outdoors or indoors at all times, depending on where they have located their environment and how long they’ve been there.
Conclusion:
We hope we have given you enough information on how to get reliable concrete resurfacing in Melbourne.
 Where To Find Concrete Resurfacing Melbourne?
You should contact Granicrete Australia to get the best Concrete Resurfacing Melbourne.
